Call us at 0086-13486123098

Our Product Detail

3 Phase Induction Motor

Both drives utilize 3-phase modulating inverters. In previous decades, DC drives 3 phase motor were regularly utilized on account of their simplicity, many machine manufacturers prefer using AC drives as of late. Also see that the rotor speed did not catch until the magnetic field. In mechanical systems, all rotating parts don't usually operate at precisely the same speed. Like many different things, simply because you're able to alter the speed of a winding design doesn't indicate you ought to do so.

Send Inquiry Now

Our Product Detail

This is the description of 3 Phase Induction Motor

 

Standard Features

  • Sinusoidal power supply of 3000v to 11,000 V
  • Motors manufactured in 2 to 16 poles
  • welded steel plates for frame 355 to 1000
  • Cooling methods used:
    - Open self-ventilated;
    - Self-ventilated by ducts, air inlet and outlet;
    - Forced ventilated, air inlet and outlet by ducts;
    - Forced ventilation, cooling on top of motor;
    - air-to-air Cooler ;- Air-to-water Cooler ;other cooling methods can be design
  • Mounting: B3
  • Degree of Protection: IP23 to IP55
  • Service duty: (S1)
  • Class of insulation: F
  • Service Factor: 1.0
  • Ambient temperature: 40 °C
  • Altitude: 1000 m
  • Temperature detector: Pt100
  • Single phase space heater
  • Bearings: Rolling bearing or Sleeve bearings
  • Electrically insulated non-drive end bearing for frames 450 and above, when connected directly to the power supply
  • Stainless steel nameplate
  • Grounding lug on the frame and terminal box
  • Grounding brush on drive end shaft for frame size 450 and above
  • Stainless steel slip rings
  • Service Factor: 1.15
  • Class of insulation: H
  • Temperature rise: 105°K for class F
  • Temperature rise: 125°K for class H
  • Ambient temperature above 40 °C (on request)
  • Altitude above 1000 m (on request)
  • Mountings: B5, B35, V1, V3, V5, V6, V18, V19, V36
  • Degree of Protection IPW55 and above
  • Classified area application: Ex-n, Ex-e, Ex-p
  • Special balance
  • Base: rail, sliding base, extended feet, rebuilt feet, anchorage plate
  • Steel welded terminal box in different sizes, based on internal available space
  • Power factor correction capacitors
  • Non-reversion ratchet
  • Centrifugal switch
  • Temperature detector: Thermistor (PTC or NTC)
  • Temperature detector: Thermostat (Bimetallic)
  • Two energized power terminal boxes
  • One or more accessory terminal boxes
  • Shaft: Special dimensions, double shaft end, tapered, hollow, special steel
  • Sleeve bearing
  • Oil lubricated bearing
  • Special bearing (overdesigned) for axial or radial thrust
  • Special painting
  • Terminal block for low voltage
  • Cable gland in the terminal box entrance
  • Protection against voltage surge: Lighting arrestors and Capacitors
  • Aluminum, copper or brass rotor
  • Vibration detector
  • Noise suppressor in the air inlet and outlet
  • Encoder
  • Tachogenerator

 

 

 

Both drives utilize 3-phase modulating inverters. In previous decades, DC drives 3 phase motor were regularly utilized on account of their simplicity, many machine manufacturers prefer using AC drives as of late. Also see that the rotor speed did not catch until the magnetic field. In mechanical systems, all rotating parts don't usually operate at precisely the same speed. Like many different things, simply because you're able to alter the speed of a winding design doesn't indicate you ought to do so.

 

The rotor cannot rotate at synchronous speed, otherwise there would not be any induced current. If it could attain synchronous speed, there would be no induced EMF in it. It is also not a magnet, though it is attracted by a magnet. An individual can observe an IC engine generates peak torque only over a really limited assortment of RPM. Starting torque will likewise be reduced. Besides that, it's a quite excellent method for the reason that it provides a large starting torque in a brief transient state, without the necessity of external equipment to help starting the motor.

 

 

As stated above, for decades the 3 phase motor was intended for a certain rpm depending on the frequency of the incoming line. The motor doesn't harm the surroundings and the machine. Motors with more than four poles are a lot less common and just employed for special applications. After the motor is multi-speed, the cycle for each speed must be entirely defined, for example, process of changing from 1 speed to another. Induction motors are somewhat more complicated to comprehend. Starting the induction motor is the most significant and dangerous step. Induction motors which have many important advantages like high reliability and performance have an important part in many industries.

 

Motors have zero doubt simplified several processes in commercial in addition to industrial setups, but have posed threats to energy resources at the exact same moment. Induction motors are somewhat more complicated to comprehend. Starting the induction motor is the most essential and dangerous step. AC induction motors have come to be an irreplaceable portion of both industrial and business establishments. An AC induction motor has a rather straightforward function. Since AC induction motors don't have any mechanisms to decrease power consumption, the consequent energy wastage is quite significant. A normal AC induction motor doesn't have any way to create adjustments in the total amount of power it consumes in connection with the work done.

 

 

The motor doesn't harm the surroundings and the machine. As stated above, for decades the 3 phase motor was intended for a certain rpm dependent on the frequency of the incoming line. Therefore, it is not surprising to be aware that the price of running motors has an immediate influence on the price we pay while buying the products. The offered reversible motors are made using premium high quality components.

 

You might also like

Leave A Message